石墨烯负载的氧配位钴单原子稳定金属锂负极

Lithium (Li)-based batteries are the dominant energy source for consumer electronics, grid storage, and electrified transportation. However, the development of batteries based on graphite anodes is hindered by their limited energy density. With its ultrahigh theoretical capacity (3860 mAh∙g⁻¹), low redox potential (−3.04 V), and satisfactorily low density (0.54 g∙cm⁻³), Li metal is the most promising anode for next-generation high-energy-density batteries. Unfortunately, the limited cycling life and safety issues raised by dendrite growth, unstable solid electrolyte interphase, and "dead Li" have inhibited their practical use. An effective strategy is to develop a suitable lithiophilic matrix for regulating initial Li nucleation behavior and controlling subsequent Li growth. Herein, single-atom cobalt coordinated to oxygen sites on graphene (Co-O-G SA) is demonstrated as a Li plating substrate to efficiently regulate Li metal nucleation and growth. Owing to its dense and more uniform lithiophilic sites than single-atom cobalt coordinated to nitrogen sites on graphene (Co-N-G SA), high electronic conductivity, and high specific surface area (519 m²∙g⁻¹), Co-O-G SA could significantly reduce the local current density and promote the reversibility of Li plating and stripping. As a result, the Co-O-G SA based Li anodes exhibited a high Coulombic efficiency of 99.9% at a current density of 1 mA∙cm⁻² with a capacity of 1 mAh∙cm⁻², and excellent rate capability (high current density of 8 mA∙cm⁻²). Even at a high plating capacity of 6 mAh∙cm⁻², the Co-O-G SA electrode could stably cycle for an ultralong lifespan of 1300 h. In the symmetric battery, the Co-O-G SA based Li anode (Co-O-G SA/Li) possessed a stable voltage profile of 18 mV for 780 h at 1 mA∙cm⁻², and even at a high current density of 3 mA∙cm⁻², its overpotential maintained a small hysteresis of approximately 24 mV for > 550 h. Density functional theory calculations showed that the surface of Co-O-G SA had a stronger interaction with Li atoms with a larger binding energy, −3.1 eV, than that of Co-N-G SA (−2.5 eV), leading to a uniform distribution of metallic Li on the Co-O-G SA surface. More importantly, when matched with a sulfur cathode, the resulting Co-O-G SA/lithium sulfur full batteries exhibited a high capacity of 1002 mAh∙g⁻¹, improved kinetics with a small polarization of 191 mV, and an ultralow capacity decay rate of 0.036% per cycle for 1000 cycles at 0.5C (1C = 1675 mA∙g⁻¹) with a steady Coulombic efficiency of nearly 100%. Therefore, this work provides novel insights into the coordination environment of single atoms for the chemistry of Li metal anodes for high-energy-density batteries.     

Solution combustion synthesis,energy and environment: Best parameters for better materials

Solution combustion synthesis (SCS) is a worldwide used methodology for the preparation of inorganic ceramic and composite materials with controlled properties for a wide number of applications, from catalysis to photocatalysis and electrocatalysis, from heavy metal removal to sensoristics and electronics. The high versatility and efficiency of this technique have led to the introduction of many variants, which allowed important optimization to the prepared materials. Moreover, its ecofriendly nature encouraged further studies about the use of sustainable precursors for the preparation of nanomaterials for energy and environment, according to the concept of circular economy. On the other hand, the large variety of expressions to define SCS and the often-contradictory definitions of the SCS parameters witnessed a scarce consciousness of the potentiality of this methodology. In this review article, the most important findings about SCS and the selection criteria for its main parameters are critically reviewed, in order to give useful guidelines to those scientists who want to use this methodology for preparing materials with improved or new functional properties. This review aims as well (i) to bring more clarity in the SCS terminology (ii) to increase the awareness of the SCS as a convenient tool for the synthesis of materials and (iii) to propose a new perspective in the SCS, with special attention to the use of ecofriendly procedures. Part of the review is also dedicated to precautions and limitations of this powerful methodology.     

化学法改性煤沥青脱除苯并芘的研究

在管式反应器中采用苯甲酸、聚乙二醇、固体古马隆树脂（S）、液体古马隆树脂（L）为添加剂来降低煤沥青中有害物质苯并芘的含量，以期使得煤沥青可绿色化应用。采用紫外-可见分光光度计分析煤沥青中苯并芘含量。考察了反应温度、反应时间、添加剂添加量、催化剂等工艺条件对添加剂脱除煤沥青中苯并芘的影响。结果表明，不同工艺条件能降低煤沥青中苯并芘的含量。在优化条件下，不同添加剂对苯并芘脱除率由高到低依次为：液体古马隆树脂、聚乙二醇、苯甲酸和固体古马隆树脂。分析其反应机理，这与催化剂的酸性相关，发生亲电取代反应。结果表明，液体古马隆树脂（L）在催化剂存在下对煤沥青中苯并芘脱除率可达73.0%，显示了良好的应用前景。     

Probing molecular environments with a fictitious isotopic dipole

A HD-like (HD: mono-deuterated hydrogen molecule) isotopic dipole moment is proposed as a sensible probe for molecular environments, in particular for electrostatic fields and polarizable (reactive) sites of molecules. Fictitious nuclear masses are chosen in order to yield a rigid dipole with a small appropriate magnitude. Upon subtracting the Born-Oppenheimer energy, the interaction is reduced to field-dipole-like and dipole-polarizability-like terms, the last one being particularly informative since connected to potentially reactive sites. Possible asymmetries of this term appear as signatures of charged sites in the molecule. The field strength and orientation are easily obtained by identifying the minimum field-dipole energy configuration and flipping the dipole from it. Tests with hydrogen, water, benzene, and chlorobenzene molecules confirm the good performance of the method. In an application to test the present models for hydrogen activation by a frustrated Lewis pair, the full potential of the method is assessed.     

基于混合空穴注入层的湿法制备高效蓝光热激活延迟有机发光二极管

在溶液法制备有机电致发光器件(OLEDs)的研究中, PEDOT∶PSS由于具有较好的成膜性与高透光性而常被用作器件的空穴注入层。但相关研究表明, PEDOT∶PSS本身稳定性较差以及功函数较低,这使得溶液法制备OLEDs的性能差且不稳定。蓝色作为全彩色的三基色之一,制备高效的蓝光器件对于实现高质量显示器件和固态照明装置必不可少。而目前溶液法制备蓝光OLEDs的器件效率普遍较差,针对此问题,本文利用传统的蓝光热激活延迟荧光发光(TADF)材料DMAC-DPS作为发光层,用溶液法制备了蓝光TADF OLEDs,通过在PEDOT∶PSS中掺杂PSS-Na制备混合空穴注入层(mix-HIL)来提高空穴注入层的功函数,研究其对于蓝光TADF OLEDs器件性能的影响。首先在PEDOT∶PSS水溶液中掺入不同体积的PSS-Na溶液,在相同条件下旋涂制膜,进行器件制备。通过观测各个实验组器件的电致发光(EL)光谱,发现掺入PSS-Na后器件EL谱存在光谱蓝移的现象,这是由于掺入PSS-Na水溶液后, mix-HIL层的厚度有所降低,使得在微腔效应作用下, EL光谱发生蓝移。通过对比各组器件的电流密度-电压-亮度(J-V-L)曲线及其计算所得器件的电流效率,结果显示随着PSS-Na的掺入,器件的亮度和电流都有所增大,器件的电流效率也得到了提升,当掺杂比例为0.5∶0.5(PEDOT∶PSS/PSS-Na)时提升幅度最大(亮度提升86.7%,电流效率提升34.3%)。通过在瞬态电致发光测试过程中施加或撤去驱动电压观测了器件EL强度的变化,分析了在混合空穴注入层/发光层(mix-HIL/EML)界面处的电荷积累情况。实验证明,通过在PEDOT∶PSS中掺杂PSS-Na制备mix-HIL获得了蓝光TADF OLEDs器件性能的提升,这是一个获得高效率溶液法制备OLEDs的可行方法。     

Spatio-Temporal Variation of the Bacterial Communities along a Salinity Gradient within a Thalassohaline Environment (Saline di Tarquinia Salterns,Italy)

The “Saline di Tarquinia” salterns have been scarcely investigated regarding their microbiological aspects. This work studied the structure and composition of their bacterial communities along the salinity gradient (from the nearby sea through different ponds). The communities showed increasing simplification of pond bacterial diversity along the gradient (particularly if compared to those of the sea). Among the 38 assigned phyla, the most represented were Proteobacteria, Actinobacteria and Bacteroidetes. Differently to other marine salterns, where at the highest salinities Bacteroidetes dominated, preponderance of Proteobacteria was observed. At the genus level the most abundant taxa were Pontimonas, Marivita, Spiribacter, Bordetella, GpVII and Lentibacter. The α-diversity analysis showed that the communities were highly uneven, and the Canonical Correspondence Analysis indicated that they were structured by various factors (sampling site, sampling year, salinity, and sampling month). Moreover, the taxa abundance variation in relation to these significant parameters were investigated by Generalized Linear Models. This work represents the first investigation of a marine saltern, carried out by a metabarcoding approach, which permitted a broad vision of the bacterial diversity, covering both a wide temporal span (two years with monthly sampling) and the entire salinity gradient (from the nearby sea up to the crystallisation ponds).     

Facile Formation of Sulfurized Nanorod-Like ZnO/Zn(OH)2 and Hierarchical Flower-Like γ-Zn(OH)2/ϵ-Zn(OH)2 from a Green Synthesis and Application as Luminescent Solar Concentrator

This research endeavors to overcome the significant challenge of developing materials that simultaneously possess photostability and photosensitivity to UV-visible irradiation. Sulfurized nanorod (NR)-like ZnO/Zn(OH)₂ and hierarchical flower-like γ-Zn(OH)₂/ϵ-Zn(OH)₂ were identified from XRD diffraction patterns and Raman vibrational modes. The sulfurized material, observed by FEG-SEM and TEM, showed diameters ranging from 10 and 40 nm and lengths exceeding 200 nm. The S²⁻ ions intercalated Zn²⁺, modulating NRs to dumbbell-like microrods. SAED and HRTEM illustrated the atomic structure in (101) crystal plane. Its direct band gap of 3.0 eV was attributed to the oxygen vacancies, which also contribute to the deep-level emissions at 422 and 485 nm. BET indicated specific surface area of 4.4 m² g⁻¹ and pore size as mesoporosity, which are higher compared to the non-sulfurized analogue. These findings were consistent with the observed photocurrent, photostability and photoluminescence (PL), further supporting the suitability of sulfurized NR-like ZnO/Zn(OH)₂ as a promising candidate for Luminescent solar concentrators (LSC)-photovoltaic (PV) system.     

Trace metal analyses in honey samples from selected countries. A potential use in bio-monitoring

Honey is a sweet product made by bees using nectar from flowers. Concentrations of Ca, K, Mg, Fe, Zn, Mn, Cu, Pb and Cd were determined in 13 honey samples from the selected regions around the world. Levels of Ca, Mg, Cu, Fe, Zn and Mn were measured using flame atomic absorption spectrometry (FAAS). Potassium concentration was determined via flame photometry. Concentrations of Cd and Pb were determined using the electrothermal technique (ETAAS). It was estimated that the examined samples of honey from Greece, Turkey, Spain, Poland, Mexico, Argentina and Italy were of good quality in terms of metal concentrations (compliant with the norms referring to food products – WHO, Fifty-third Report of the joint FAO/WHO Expert Committee on Food Additives; Technical Report Series 776, Geneva), although the analysed samples were not free of heavy metals. The concentrations of the elements in the honey samples ranged from 2.38 to 9.31 μg · g^?1 for Zn, from 3.86 to 35.10 μg · g^?1 for Fe, from 0.19 to 21.64 μg · g^?1 for Mn, from 49.53 to 1006.90 μg · g^?1 for Ca, from 388.25 to 4761.50 μg · g^?1 for K and from 0.20 to 1.53 μg · g^?1 for Cu and regarding heavy metals from 0.11 to 2.78 μg · g^?1 for Pb and from 0.02 to 0.44 μg · g^?1 for Cd. According to these results it was found that the concentrations of heavy metals in the honey samples (except for alfalfa honey and eucalyptus honey from Italy) were under the acceptable limits for foods set out by the FAO/WHO. It was confirmed that the application of chemometric tools supports the extraction of significant information from analytical data, even though the availability of samples is not fully sufficient (this problem is often encountered in environmental analyses).     

氧化环境和比例对改性Hummers法制备GO的影响

以鳞片石墨(GR)为原料,采用改性Hummers法液相氧化方法制备氧化石墨,通过超声剥离的方法剥离出片状的氧化石墨烯(GO),探讨了H₂SO₄环境与H₂SO₄+H₃PO₄混酸环境和KMnO₄与GR的比例对GO制备的影响。采用FTIR、UV、TG、XRD、SEM和XPS等分析手段对制备的GO进行分析。结果表明：GO外貌是呈褶皱片状,在片层上主要有C=O、C-OH、-COOH和C-O-C等官能团,以共价键形式存在石墨层间;通过TG与XPS数据分析表明在H₂SO₄ H₃PO₄混酸环境下制备的GO含氧官能团较多,并且(KMnO₄)与鳞片石墨的最佳比例是1:4。